- TRANTER FARMERSVILLE ILLINOIS HOW TO
- TRANTER FARMERSVILLE ILLINOIS SERIAL
- TRANTER FARMERSVILLE ILLINOIS MANUAL
- TRANTER FARMERSVILLE ILLINOIS SERIES
The gasket material is selected for compatibility with the fluids being processed and the operating temperatures. The gaskets are single piece, molded construction, and generally bonded to the plates with Pliobond 30 adhesive. Superchanger Frame, Models HJ, UJ, SJ and MJ. The number and location of the holes is dependent upon the design conditions. Fluid passage holes are pierced at the corners of each plate. There are grooves around the circumference of the plates which accept the sealing gasket and also add reinforcement because of the ribbed edges. Superchanger Frame, Models HP, UP, SP, MP and FP.Īll plates are manufactured from die-formed sheet metal in virtually any material that can be cold worked, such as stainless steel, titanium, Alloy C-276, Alloy-20, etc. It is also well suited for equal flows and close approach. GX Series: An asymmetrical four quadrant plate suited for low viscosity and close temperature approach applications or processes involving two vastly different flow rates. GF Series: Wide gap and parallel (washboard) patterns are designed for applications where there are high viscosity fluids or fluids containing fibers or coarse particles.
TRANTER FARMERSVILLE ILLINOIS SERIES
UX, SX and GC Series plates: Herringbone (chevron) pattern is ideally suited for handling aqueous solutions. Depending on the applications, the GF, UX, SX, GC and GX Series plates are used to achieve maximum heat transfer. SUPERCHANGER plate corrugations are available in four patterns. Upper Guide Bar Straight Nozzle Support Column “P” Frame Plate Pack Elbow Nozzle This information is helpful when contacting the factory. IDENTIFYING YOUR SUPERCHANGER® UNIT If the Customer Tag is missing on delivery, the SO# is stamped in the top right corner of the stationary frame.Ī data plate like the one shown on the picture above is fixed to the stationary frame of the unit and provides the following information.
TRANTER FARMERSVILLE ILLINOIS SERIAL
* Tranter must have serial or drawing number to properly identify your equipment.įor PHE parts, service or performance ratings, contact one of Tranter’s authorized Service Centers (see full information for contacting on page 46). Upon delivery of your SUPERCHANGER unit(s), be sure to record the information from the Data Plate on each unit in case the nameplate is destroyed, lost or becomes illegible. General Maintenance Ordering Parts Returned Material Damaged Shipments Additional InformationĮQUIPMENT LOG SHEET You will need the information shown in the table below whenever you contact the factory for service.
TRANTER FARMERSVILLE ILLINOIS HOW TO
Leakage Between the Plate Pack and the Frame Leakage Between the Nozzle and the End Frame Leakage Between the Plates to the Outside of the Unit Mixing of Fluids Increase in Pressure Drop or a Reduction in Temperature Reading How to Find a Defective Plate With Through Holes
TRANTER FARMERSVILLE ILLINOIS MANUAL
Steps for Manual Cleaning of Plates Plate Cleaning Tips Cleaning-In-Place (CIP) Back Flushing and Strainers Cleaning Guidelines Removing Old Gaskets Installing Continuously Glued Gaskets Installing Spot-Glued Gaskets Installing SUPERLOCK® Snap-In Gaskets Installing Teflon Encapsulated Gaskets and Unit Assembly Installing Clip-On Gaskets Shutting Down the Unit Disassembly Procedures Removal of Plates Replacing Plates Replacing Gaskets Tightening the Plate Pack Tightening Sequences Precautions Prior to Start-Up Gaskets-Glued Gaskets-Glueless Gasket Storage Procedures Mixed Gasket Materials GX Gluing Codes GX Start and End Plate Explanations Pass Arrangement Flow Arrangement Drains Connecting “C” Framesĭrawings Four-Plate Sequence Multi-Pass Units Plate Details Unit Part Numbers Plate Material and Date of Manufacture Data Model Nomenclature Frame Pressure Ratings Condensed Unit Specifications Plate Pack Widths Plate Pack Tightening Dimensions Plate Designations Drawings Element Composition Diagram Plate Hole Designation for UX, SX, GC and GF Series